* If the firmware is 3.0.1 or later versions, the wall smart switch enters the“Quick Pairing Mode”instantly when you power it on.
* If the wall switch has been paired with your app before, long press any button for about 5s until the Wi-Fi LED indicator changes in a cycle of two short and one long flash to enter the“Quick Pairing Mode”and long press another 5s until the Wi-Fi LED indicator flashes to enter the “Compatible Pairing Mode (AP)”.
Buy a TX Wi-Fi smart wall light switch: http://bit.ly/TXswitch
More tutorial videos are available.
- What's new: https://youtu.be/9UIX5VF8kgY
- Main app features: https://youtu.be/oxSq60Bo_VA
- Pairing with the RM433 remote controller: https://youtu.be/qvRKzQsm3NY
What kind of tutorial videos you want to watch? Comment below to share your opinions with us. 😉
Comments • 15
@ayadalkalidi1617 --> You helped me a lot@tuffyman3067 --> I am struggling to connect with 2.4mhz ?
@neillondon8709 --> Rocket science would be easier. ..
@shyamsunder9843 --> What are you trying to show , scrap the stupid music first
@senhorcoelhoo --> Hello, I recently bought the TX2C model switch and did the whole configuration and it is operating normally. But when I try to add it to the iPhone widgets it doesn't appear in the list. I also have two of the TX1C model that appears normally. Can you help?
@wayneabroue7896 --> I bought a dual to use the timer loop to control my greenhouse pumps. Well what a huge disappointment. Linking to ewelink was the easy part. But surprise no loop timer. Thought it required purchase.. nothing again. No loops rendering this device useless. Tried DIY mode. Yep connects no webpage. Deleted device in ewelink,, still no webpage in DIY mode. Forced to open and solder. Great,, nope. Flash fail, can't connect to device. Checked and and pin 1 bridge... Still nothing..not connecting to serial. USB serial proper connection etc. Removed the wires, reconnect AC. Dead. Nothing, nada, zilch. Brick... What rubbish. Yes, I've flashed many esp devices before. Not my first rodeo. It's a scam to advertise loop timing... On original software. Now I'm out of pocket,, Guess I'll just stick to the trusted nodemcu and relays.
@briankgopane7629 --> Sonoff produces good quality product but their tutorials are horrible, totally useless
@laurenhealey2904 --> Some segments in the video are stamped not adjacent to each other
@Coppillie --> Have 3 switches that were all working fine until I got a new router. Now none of them will pair (yes, I’ve tried the obvious) and also, the touch buttons don’t work very well…. It often takes many attempts for my finger to be able to switch
@ianmilne6349 --> This video is useless
@beaker8501 --> Video is too quick and should have language.....
@marcelohuguenin1524 --> Can you show the connection with 4.0 for IOS?
@monklesavinsen6644 --> JUNK DO NOT BUY THIS JUNK ..........I bought a basic and a ch4 both JUNK neither will pair with my wifi and both indicate same "offline" on ewelink app. JUNK JUNK JUNK.
@Yet_Another_Steve --> SNEEZE. And they're paired. If only it were that easy... I'll keep trying, of course. Until I get it to work. Edit: went to get a charger for the phone leaving it with a not connected message, when I got back it was connected. Good people of Sonoff world, try just leaving it to connect even with an error message.
@PVflying --> Why don’t you make products which actually work? The pairing with eWeLink app is a total disaster. I will use PayPal chargeback to get a full refund for my NON WORKING SONOFF JUNK